Skip to content
PahrumpWellService

Local Guide · Published November 9, 2026

How to verify a Nevada well driller or pump contractor before you hire in Pahrump

As of November 2026, well work in Pahrump, NV runs under two separate Nevada licenses: drilling, deepening or plugging a well requires a well-drilling license from the State Engineer (Division of Water Resources, NRS 534.160), while installing or repairing a pump, pressure tank or storage tank is contractor work under the State Contractors Board’s C-23 classification (NAC 624.400). Both lookups are free and take about two minutes each.

Pahrump Well Service · (775) 571-7931

Quick answer

Drilling, deepening, plugging: check the driller at the Division of Water Resources’ Driller Search — and the company at the Contractors Board, because a rig owner needs both. Pump or tank work on an existing well: check the company at the Contractors Board for an active C-23.

A technician servicing a submersible well pump at a wellhead — illustrative stock photo, not an actual Pahrump job site

Two agencies, two licenses — and why Pahrump homeowners mix them up

Most Nevada trades have one licensing body. Wells have two, and the split follows the work, not the company. Chapter 534 of the Nevada Revised Statutes, the state’s groundwater law, says a person “shall not drill a well for water in this State without having first obtained a well-drilling license” (NRS 534.160), and it puts that license in the hands of the State Engineer: every well driller must apply to the State Engineer annually, and the licenses expire each June 30 and are not transferable (NRS 534.140). The same section then adds the second layer most people miss — a driller who owns, leases or has a contract to buy a drilling rig must also obtain a license from the State Contractors Board.

The Contractors Board side is classification C-23. The regulation, NAC 624.400, calls it “drilling wells and installing pumps, pressure tanks and storage tanks considered integral to water wells,” and says a C-23 holder “may install and repair water wells, pressure tanks, storage tanks and pumps by boring, drilling, excavating, casing, cementing, dewatering and cleaning to provide a supply of uncontaminated water.” That is the license that covers the job most Pahrump homeowners actually hire for — a submersible pump replacement or a pressure tank swap on a well that already exists.

The State Engineer’s well-drilling license, meanwhile, is scoped by NAC 534.294: it authorizes the holder “to drill, plug or rehabilitate” water wells and monitoring wells, and the State Engineer may issue limited licenses tied to a class of work or type of rig. The chapter sets up no separate pump-installer license, and the Division of Water Resources’ own program page describes only licensed well drillers. So the plain reading for a homeowner:

The job Whose license, under what Where to check
New or replacement well; deepening, recasing, relining, resealing, reaming (rehabilitation); plugging Well-drilling license from the State Engineer (NRS 534.140, 534.160; NAC 534.294) plus a Contractors Board license for the rig owner (NRS 534.140(8)) Driller Search at tools.water.nv.gov, then the Board’s License Search
Pump replacement or repair; pressure tanks and storage tanks “considered integral to” the well Contractors Board classification C-23 (NAC 624.400) The Board’s License Search
Chemical treatment, brush cleaning, surging, jetting of an existing well (reconditioning) Defined separately from rehabilitation (NAC 534.188) — this page does not resolve which license it falls under; ask the Division Division of Water Resources, (775) 684-2800

Quoted and paraphrased from NRS chapter 534, NAC chapter 534 and NAC 624.400 as published by the Nevada Legislature, read November 2026. The statutes and regulations are the authority; this table is orientation.

Why the drilling license matters even if you never see the rig

The well-drilling license is not a formality. The regulations attach duties to it that protect the person paying for the hole. Under NAC 534.330, the licensed driller “shall directly supervise the well-drilling site when the drill rig is in operation” — if that person leaves, the operation must shut down until a licensed driller is back — and must carry the license card on site. Under NAC 534.350, the drilling contractor’s name and address must be displayed on the rig in letters at least three inches high. Under NRS 534.170, the driller must keep a log of the strata, the water-bearing zones, the casing, the seal and the yield, and furnish it to the State Engineer within 30 days of completion; it becomes the permanent state record of your well, and the thing a future buyer’s inspector will ask for. And under NRS 534.160(5), a well drilled by an unlicensed person is ordered plugged — at the owner’s expense if it is not done within 30 days.

Deepening deserves one more sentence, because it is the Pahrump job. NAC 534.189 defines rehabilitation as “a material change in the design or construction of an existing well, including, without limitation, deepening, hydrofracturing, recasing, perforating …” — and rehabilitation is squarely inside what a well-drilling license authorizes. Our Order 1293 guide covers the water-rights side of deepening and replacement (neither is restricted by the order); this page covers who may legally run the rig.

The eight-point license check

Open both lookups — the Division’s Driller Search and the Board’s License Search — and walk the records top to bottom.

  1. Sort the job into drilling or pump work. Drilling a new or replacement well, deepening, recasing or otherwise rehabilitating a well, or plugging one is well-drilling work — it needs a well driller licensed by the Nevada State Engineer (Division of Water Resources), and a company that owns or leases the rig also needs a State Contractors Board license. Replacing or repairing a pump, pressure tank or storage tank on an existing well is contractor work under the Board’s C-23 classification. Many Pahrump outfits do both; the records should show both.
  2. Get the license number(s) off the quote. Nevada law requires all advertising by a licensed contractor to carry the company name and the Contractors Board license number, and a residential contract must state that number and the monetary limit on the license. For drilling, also ask for the well driller’s own license number — the regulations require the licensed driller to carry the license card on site. A company that cannot produce the numbers has answered the question.
  3. Run the Division of Water Resources Driller Search. Open tools.water.nv.gov/DrillerSearch.aspx. It is a filter form with four drop-downs — Name, Company, City and License — and a Submit button; Pahrump is one of the cities in the list. Pick the driller’s name or the company and submit. If the person who will be running the rig is not on the list, that is the finding. The Division’s own footer says it makes no guarantee the posted information is current, so confirm anything doubtful with the Division at (775) 684-2800.
  4. Run the State Contractors Board License Search. Open the Board’s License Search at app.nvcontractorsboard.com. It offers three ways to search: by license number, by company name, or by the name of a principal or qualified individual. At least two characters are required, and the Board allows wildcard searches — “*Pike*” finds any name containing Pike. Search by number when you have it.
  5. Match the company name to the paperwork. The licensed business name on the record should be the name on the quote and the name you will write any check to. Not a trade name, not a person’s name, not a brand. Nevada’s Residential Recovery Fund has denied a claim where the deposit was written to a company’s other trading name rather than the exact licensed name, so the match matters beyond the hire.
  6. Read the status, the classification and the monetary limit. Only an active license counts. On the Board record, look for classification C-23 — the regulation describes it as drilling wells and installing pumps, pressure tanks and storage tanks. Every Nevada contractor license also carries a monetary limit, and the contract must state it; if the limit is lower than the price of your job, that is a question for the contractor and the Board before the work starts. Screenshot both records with the date showing.
  7. For drilling, check the paperwork the driller owes the state. A licensed driller files a notice of intent before drilling, must directly supervise the site whenever the rig is running, must display the contractor’s name and address in letters at least three inches high on the rig, and must send the State Engineer a well driller’s report — the log of the strata, casing, seal, depth and yield — within 30 days of finishing. Ask who files these and ask for a copy of the completed report; it becomes the permanent state record of your well.
  8. Ask for what the records do not show. Ask for a current certificate of liability insurance naming you as certificate holder, ask whether the crew carries workers’ compensation, and — for any new well — ask how the quote accounts for Order 1293’s water-rights requirement, which does not apply to replacing or rehabilitating an existing well. Keep the answers with the signed contract and the well driller’s report.

To be explicit about what this site is

Pahrump Well Service is an independent referral and information site — we connect you with independent, local well and water-treatment professionals, but we don't drill wells, install pumps, or do the plumbing work ourselves. We're the connector, not the crew. Providers we refer report holding applicable Nevada licenses — always verify licensing and insurance yourself before hiring. Pahrump Well Service holds neither a well-drilling license nor a C-23. The licenses you verify belong to the independent company that does the work.

Three Nevada contractor rules that make a quote checkable

1. The license number has to be on everything

NRS 624.720(4): “All advertising by a licensed contractor must include the name of the contractor’s company and the number of the contractor’s license.” Subsection (2) requires anyone not licensed who advertises construction work to say so in the advertisement, and subsection (5) makes it unlawful to advertise with a license number that does not belong to you. A number on the truck that comes back to a different company name is not a clerical error. It is the finding.

2. The down-payment cap — and its one exception

For a residential improvement contract with an owner-occupant, NRS 624.970(2)(g) limits the initial down payment or deposit to $1,000 or 10 percent of the aggregate contract price, whichever is less. On a new well priced in the tens of thousands, that means $1,000. The statute’s exception: the cap does not apply if the contractor has filed a bond with the Board solely for the protection of consumers in the amount of $100,000, or has been granted relief by the Board. A contractor asking for more should be able to show you that bond; if they cannot, the request is outside the rule.

3. The contract itself is regulated

The same section lists what a residential improvement contract must contain: the contractor’s name, address, license number and the monetary limit on that license; the date signed and the estimated completion date; a description of the work; the total price including taxes; the deposit within the cap; and a statement that any change in scope or price must be agreed in writing as a change order. A change order not set out in writing and accepted by the owner is not enforceable against the owner — which matters on a drilling job, where “we hit rock” is the classic mid-job price change.

The Residential Recovery Fund, and the name on the check

Nevada maintains a Residential Recovery Fund administered by the Contractors Board. Under NRS 624.510, if the Board determines an injured person is eligible, it may pay actual damages out of the fund up to $40,000 per claim. Eligibility has conditions — who you are, what was built, whether the contractor was licensed — and this page does not restate them; read the Board’s Recovery Fund pages before relying on it. One thing is worth knowing before you write a single check: the Board has denied a claim where the deposit was written to a company’s other trading name instead of the exact licensed business name. Match the name on the license record, the contract and the check — exactly.

What clean records still don’t tell you

Red flags the check turns up

Our guide to choosing a Pahrump well and pump company covers the rest of the hiring conversation. The two records, read on the day you hire, are the only part of it that is a fact.

Sources and how current this is

The well-drilling license requirement, its annual term and the rig-owner Contractors Board rule are from NRS 534.140 and 534.160; the driller’s log from NRS 534.170; the license scope, site-supervision, rig-marking and rehabilitation/reconditioning definitions from NAC 534.294, 534.330, 534.350, 534.189 and 534.188; the C-23 scope from NAC 624.400; the small-job exemption from NRS 624.031(6); the advertising rules from NRS 624.720; the contract elements and down-payment cap from NRS 624.970; and the Recovery Fund cap from NRS 624.510 — all read from the Nevada Legislature’s published chapter text at leg.state.nv.us in November 2026. The Driller Search layout and the Division’s phone number are from tools.water.nv.gov; the Board’s search options and contact lines are from its License Search and consumer checklist pages, read the same month. This page deliberately does not state license fees, exam content, bond amounts, Recovery Fund eligibility details, whether a county permit attaches to pump work, or any company’s license status; read those from the agencies directly. Laws change in each legislative session and the records on the day you hire are the authority, not this page.

Related guides

Nevada well and pump licensing questions

Who licenses well drillers in Nevada?

The Nevada State Engineer, through the Division of Water Resources. As of November 2026, NRS 534.160 says a person shall not drill a well for water in Nevada without first obtaining a well-drilling license, and NRS 534.140 requires every well driller to apply to the State Engineer annually for that license. The same section adds a second layer: a driller who owns, leases or is buying a drilling rig must also hold a license from the Nevada State Contractors Board. The public lookup for the state-engineer license is the Division’s Driller Search.

Does a well pump installer need a license in Nevada?

Pump and tank work on an existing well is contractor work licensed by the Nevada State Contractors Board. NAC 624.400 creates classification C-23 — “drilling wells and installing pumps, pressure tanks and storage tanks” — and says a C-23 holder “may install and repair water wells, pressure tanks, storage tanks and pumps.” The State Engineer’s well-drilling license, by contrast, covers drilling, plugging and rehabilitating wells; the chapter that creates it does not set up a separate pump-installer license. So for a pump replacement, the record to check is the Contractors Board’s.

What is the difference between rehabilitating and reconditioning a well?

The State Engineer’s regulations draw the line. NAC 534.189 defines rehabilitation as “a material change in the design or construction of an existing well,” including deepening, hydrofracturing, recasing, perforating, installing casing or liner pipe, resealing and reaming. NAC 534.188 defines reconditioning as revitalizing a well “by various methods that do not cause a material change in the design or construction,” such as chemical treatment, brush cleaning, surging and high-pressure jetting. A well-drilling license authorizes drilling, plugging and rehabilitation. Deepening a Pahrump well is rehabilitation — licensed drilling work.

What happens if someone drills a well without a license?

NRS 534.160(5) directs the State Engineer to order any person who drills a well without a license to plug it; if it is not plugged within 30 days, the State Engineer plugs it at the expense of the person who owned or drilled the well. The same section says a licensed driller who lets an unlicensed person drill or do well-drilling work, except under the licensed driller’s supervision, has his or her license revoked or not reissued. The person paying for that well is the one left without water.

Is there a $1,000 handyman exemption for well pump repairs in Nevada?

Nevada’s contractor law does exempt “any work to repair or maintain property the value of which is less than $1,000, including labor and materials” — but NRS 624.031(6) attaches exceptions, among them work that needs a building permit, work of a type performed by a plumbing or electrical contractor, work in a classification the Board says significantly affects public health and safety, and work that is part of a larger project. This page does not decide which of those reaches a given pump job. Practically, a submersible pump replacement at Pahrump well depths is far above that figure anyway — see our pump replacement cost guide — so the question for a quote is simply: who holds the C-23?

How do I look up a contractor’s license in Nevada?

Use the Nevada State Contractors Board’s online License Search. You can search by license number, by company name, or by the name of a principal or qualified individual; the Board’s instructions allow partial and wildcard searches with a two-character minimum. The Board’s licensing and customer-service lines are (775) 688-1141 for Northern Nevada and (702) 486-1100 for Southern Nevada, Monday through Friday, 7:00 AM to 4:00 PM. For the well-drilling license, use the Division of Water Resources’ Driller Search instead.

How much can a well or pump contractor ask for up front in Nevada?

For a residential improvement contract with an owner-occupant, NRS 624.970 caps the initial down payment or deposit at $1,000 or 10 percent of the aggregate contract price, whichever is less. The one exception: the cap does not apply if the contractor has filed a consumer-protection bond with the Board in the amount of $100,000, or has been granted relief by the Board. On a new well priced in the tens of thousands, a demand for half up front is outside the rule unless the contractor can show you that bond.

What is the Residential Recovery Fund?

A fund administered by the Nevada State Contractors Board. Under NRS 624.510, if the Board finds an injured person eligible, it may pay actual damages out of the fund up to $40,000 per claim. Eligibility turns on who you are, what was built and who you hired, so read the Board’s Recovery Fund pages before counting on it — and write every check to the exact licensed business name, because a claim has been denied over a check written to a company’s other trading name.

Free · No obligation

Get quotes you can verify before anyone shows up

Tell us what's going on with your well and a pre-screened independent local pro will call you back — usually the same day.

Prefer to talk? Call (775) 571-7931 — fastest for no-water emergencies.

Call (775) 571-7931 Free Quote